Profile material EPDM or TPE IP65 protection grade Integration of contacts and shape Internal safety contact Original cover and wire connector at the end Various sizes available, maximum length 6100mm |
product model
Product number | SGE1525TT | SGE2530 | SGE2545 |
Material | TPE | EPDM | EPDM |
Material hardness | 65 shore A | 65 shore A | 65 shore A |
Product Size (Width*Height) | 15mm*25mm | 25mm*30mm | 25mm*45mm |
Protection level | IP65( Optional IP 68) | IP65( Optional IP 68) | IP65( Optional IP 68) |
Operating temperature | -10~50℃ | -10~50℃ | -10~50℃ |
Capacitor voltage | 24V 100mA | 24V 100mA | 24V 100mA |
Safety standard | EN ISO 13856-2 /EN 12978 /EN ISO 13849-1 /UL 325 |
Ordering Information
Note:
* The standard material for most configurations is EPDM.
(Exception: The standard material used for SGE1525TT is TPE).
** Angled aluminum mounting channels are available in all shapes except SGE1525TT.
*** For example, 150C=150mm long cable, 150MQD=150mm long cable with a quick disconnect male connector at the end.
|
Product Features
material: | EPDM | |
Material hardness: | 65 Shore A | |
Maximum single length: | 25m | |
Protection level: | IP65 | |
Mechanical force: | 500N | |
Switching cycle: | 105 | |
Switch angle: | 2*20° | |
Starting resistance: | ≤100Ω | |
Electrical capacity: | 24V 100mA | |
Operating temperature: | -20~55℃ | |
Maximum operating temperature: | -20~75℃ | |
Maximum length of contact cable: | 100m | |
Maximum number of serial connections: | 10 connections | |
No action end zone: | 20mm | |
connecting cables: | 2 leads,34mm2 |
Chemical resistance:
characteristic | TPE (SGE1525TT) | EPDM (SGE2530TT, SGE2545TT) |
Tearing force (resistance) | 3 | 3 |
Ultimate stretchability | 3 | 3 |
Rebound time at 20℃ | 2 | 2 |
Resistance to permanent deformation | 3-4 | 2 |
abrasion | 3 | 3 |
Elongation when tearing | 4-5 | 3 |
Low temperature elasticity | 2 | 2 |
High temperature stability | 4 | 2 |
Oxidation stability | 1 | 1 |
UV stability | 1 | 1 |
Resistant to open air/air | 1 | 1 |
Fire resistance | 6 | 6 |
Gas permeability | 3 | 4 |
Characteristic | TPE (SGE1525TT) | EPDM (SGE2530TT, SGE2545TT) |
Water resistance | 1 | 1-2 |
Dilute acid | 1 | 2 |
Diluent | 1 | 2 |
Non-oxidizing acid | 2 | 2 |
Oxidizing acid | 2 | 4 |
ASTM oil #3 | 2 | 6 |
Vegetable oil | 1-2 | 5 |
Organic solvents | 2-3 | 2 |
Ketone solvent (oxygenated) | 2-3 | 3 |
Hydrocarbon | 2-3 | 5-6 |
alcohol | 1 | 1 |
The essential:
1=Very good; 6=Insufficient
EPDM ethylene and propylene rubber: good
Resistance to ozone and erosion, especially suitable for aggressive chemicals.
TPE thermoplastic elastomer.
The essential:
1=Invalid, permanent contact
2=Almost ineffective, a little contact
3=General effect, general contact
4=Significant effect, reduce contact
5=Serious effect, very brief contact
6=Extreme effect, avoid contact
Lihong Safety Equipment Engineering (Shanghai) Co., Ltd.
E-Mail: info@lh-safety.com
Address: 581 Xiuchuan Road, Chuansha Town, Pudong New District, Shanghai
(Greenland East Coast International Plaza-Room A 313)
Copyright © Lihong Safety Equipment Engineering (Shanghai) Co., Ltd. ICP 19034341-1 Technical support: Yuanma Technology