Milling machine protection
| · Customized patent protection device · Multiple micro switches control the direction of the protective cover switch · Large window for easy viewing of processing quality Comply with (GB/T 16855.1-1997) Class 1 or Class 3 stop requirements; comply with the relevant regulations and requir ements of GB5226.1-2002 10.7, and GB 16754; · The safety control system meets the SIL3 safety level: safety products are preventive protection measures, are active protection measures, and accept custom-made special sizes. |
Milling machine protection selection
Product name | AG61-CG40 | AG61-CG50 | Security door lock | Safety control system |
Dimensions | A:454 B:450 C:500 D:200 | A:504 B552 C:580 D:220 | √ | √ |
Explanation |
Product technical description
· Control of access to the hazardous area The design and positioning of the protective cover of the movable lathe should be such that it can prevent the protective cover from closing when there are people left in the hazardous area during normal operation. If this is not feasible, other measures should be taken to prevent the detection of persons in the danger zone. See GB/T 15706-2012, 6.3.3.2.3. |
· Safety chain (conforming to ISO 14119) Safety door locks that meet international safety requirements. Confirm safety and security through a third-party certification body. · Conforms to: ANSI B11.13, ISO 13849 · This protective cover has Chinese national patent · Easy to install (including installation guide) · Including one year of non-artificial maintenance |
Product patent
· Product patent number: ZL 2014 2 0692706.4 · Safety design considerations The design of the milling machine protective cover should properly consider the operation of the machine for the foreseeable full life cycle and the predictable machine environment Factors, poor consideration can lead to dangerous conditions that hinder the operation of the machine, which in turn leads to the protective cover provided Was artificially abandoned, thereby exposing the operator to greater risks. Foreseeable aspects of existing operating shields All are properly considered in the design stage to ensure that the design and manufacture of the protective cover itself does not create new dangers. |
Milling machine safety circuit module
SR301 safety relay
Multiple safety product component inputs
· Built-in self-diagnosis function to detect faults · Optional manual/automatic reset |
| SR 103 safety controller
• Built-in self-diagnosis function to detect faults • Can choose automatic reset or manual reset • The terminal block is a finger safety protection structure • Obtained TÜV Rheinland certification |
车床防护装置· 保护卡盘卷入点伤害· 防碎削飞溅· 安全联锁监控防护罩使用状态· 配置安全控制箱回路· 安装指示灯方便查看报警状态· 满足GB T 8196-2018机械安全防护装置固定式和活动式防护装置设计和制造一般要求防护选型产品名称AG61-CG40AG61-CG50安全......
铣床防护装置 当铣床防护罩摆动,微动开关上的正极触电打开发送急停信号给机器;并连接到设备的安全回路;铣床防护罩连锁安全防护装置设计符合国家安全标准,结构稳固符合人机及现场,保护第三者的安全;符合EN418标准要求;所有的开关由欧洲分类方法E Exdllc T6,NEMA 4......
钻床防护罩专利号:2015 2 0657430.0 钻床运转过程中,操作区产生飞溅的炽热碎屑和火花,机器的旋转部件也会危及人员的安全; 提高钻床作业过程中的安全性能,避免操作者的双手直接接触到高速旋转的......
一种铆钉机的智能安全保护系统专利号:2018101420997.0当前市场上使用的铆钉机没有任何对操作人员进行保护的防范措施由于生产加工阶段高频率操作,大约每三秒就需要启动一次铆钉机,而操作人员需要手动上料,在上料过程中,自己有可能不小心误启动设备,造成对手指的损伤,......
Lihong Safety Equipment Engineering (Shanghai) Co., Ltd.
E-Mail: info@lh-safety.com
Address: 581 Xiuchuan Road, Chuansha Town, Pudong New District, Shanghai
(Greenland East Coast International Plaza-Room A 313)
Copyright © Lihong Safety Equipment Engineering (Shanghai) Co., Ltd. ICP 19034341-1 Technical support: Yuanma Technology